Thread
Print

puffer thirt printer acrorip software manual

puffer thirt printer acrorip software manual

acrorip software to use
The first step:
Insert cd, download and install the software. When prompted, press "next" to finalize. Then insert a U disk, double-click.

Step Two: Click the red circle, select English. Then turn off the page, the menu will re-open the software all into English.

  








Step Three: Click the red circle File-Open, open the picture to be printed.

  


Step Four: Click the red circle Layout menu to adjust the software on the right of the picture data.

  

Step five: Click the menu: Printer, Color, White to choose the menu of the printer.
Such as: the printer model, print color, size, resolution, and so on.

  
Note: When printing with white ink and colored ink, Color menu in the lower right inside the red circle color inkjet transfer rate of 20% to 30%, the ratio of the white inkjet transfer of 20% to 30%, the effect excellent. Range 0% to 200%, but also to adjust itself to test print results.
  
Step Six: If you want to hit white ink, Color menu in the top of Ink channel Select CMYKWWW W.
  
Step Seven: After the completion of the transfer menu, right click on the image, select Print.
  
Step Eight: If you want to hit white ink, should be left White Setting the Copies tune into "1"
Color Setting the Copies will be transferred to "0." Then press the Print to.
  
Step Nine: After printing the white ink of 10 to 15 minutes. Then color in the play. Note that this time should be
Will: White Setting the Copies tune into "0" Color Setting the Copies will tune into "1." Print.
  
The above method is to use low-solvent printing ink and white ink printed on glass, acrylic, ceramic and other media. The print data is the company doing the test sample data to obtain the best effect, only as a reference. Customers can adjust the data to print out the best results.

Cotton T-shirt printing method

The first step: the cotton T-shirt flat on the heat transfer machine, press 10 seconds (temperature of 120 degrees to 140 degrees) so it is more smooth surface.
Step two: pre-treatment liquid sprayed in the T-shirt uniform top, and then heat with a thermal transfer machine surface pre-treatment solution of water vapor will evaporate, about 30 seconds. Then press 10 to 50 seconds, 2 times every 10 seconds (temperature of 160 degrees). Once on shore, do not immediately hit the best Ink white ink, and other 30 to 60 seconds after the fight Ink. Ink is also a kick after the first heat with a heat transfer surface of the machine so that the ink to dry some, then about 30 seconds - 15 seconds to 20 seconds, 2 times (temperature of 160 degrees) every 10 seconds.
The third step: Use the software for playing textile white ink print white ink according to the above mode of operation the software first hit white ink, color ink and then immediately call back. (150% concentration of white ink, color ink concentration of 70%) with excellent results. Can be adjusted according to customer demand levels. If a direct hit in a white T-shirt, the color ink concentration adjusted to 80% to 100% for the best effect.www.tshirtprinter.cc







acrorip 软件使用方法
第一步:
插入cd,下载安装软件。根据提示,按“next”最后完成。然后插入U盘,双击 。

第二步: 单击 红圈,选择英语。然后关掉该网页,重新打开软件所有菜单将会变成英语。










第三步:单击红圈 File-Open,打开将要打印的图片。




第四步:单击红圈 Layout 菜单,调整软件右方图片的各项数据。



第五步:单击各菜单:Printer, Color,White 选择适合该打印机的各项菜单。
如:打印机型号,打印颜色,大小,分辨率等等。


注意:将白墨和彩墨一起打印时,在右下方的Color的菜单里面 将红圈的彩色喷墨比率调为20%~30%,将白色喷墨的比率调为20%~30%,效果极佳。范围是0%~200%,也可自行调节来测试打印的效果。

第六步:如想先打白墨,在Color的菜单上方有 Ink channel里选择 C M Y K W W W W.

第七步:各项菜单调完以后,在图片上点击鼠标右键,选择Print。

第八步:如想先打白墨,应将左边的 White Setting 的Copies 调成 “1”   
将Color Setting 的Copies 调成“0”。然后按Print 即可。

第九步:打印完白墨后等10~15分钟。然后在打彩色。注意此时应该
将:White Setting 的Copies 调成 “0” 将Color Setting 的Copies 调成“1”。打印即可。

上面的打印方法是使用弱溶剂墨水和白墨打印在玻璃,亚克力,陶瓷等各种介质中。各项数据是我公司在进行打印样品测试时取得效果最好的数据,只作为参考。顾客可以调节各项数据使其打印出最好的效果。

打印纯棉T恤的方法

第一步:将纯棉T恤平整的放在热转印机器上,压10秒(温度为120度~140度)左右使其表面更平整。
第二步:将前处理液均匀的喷洒在T恤上面,然后用热转印机器表面的热量将前处理液的水蒸气蒸发掉,大概30秒左右。再压10~50秒,2次,间隔10秒(温度为160度)。打完白墨最好不要马上打彩墨,等30~60秒后再打彩墨。打完彩墨后也是先用热转印机器表面的热量使其墨水干燥一些,大概30秒左右后再用15秒~20秒,2次,(温度为160度)间隔10秒。
第三步:使用软件,如需打纺织白墨按上面软件打印白墨的操作方式先打白墨,然后马上再打彩墨。(白墨的浓度为150%,彩墨的浓度为70%)效果极佳。根据顾客的需求可调节浓度。如果直接打在白色T恤上,将彩墨的浓度调为80%~100%效果为最好。

TOP

Thread